Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Coppell
If you’re in Coppell and a gate post has shifted out of plumb or a 1990s operator finally quit, here’s the direct answer: most gate parts and welding repairs here cost between $180 and $2,800 depending on whether we’re resetting a post, welding a hinge back, or replacing an obsolete control board. We get to Coppell the same day for urgent failures, usually within a couple of hours. You’ll talk to a live person when you call (903) 829-4499, and the price you’re quoted is the price you’ll pay. Hal Gatewood has been at this since 2001, and his name is on every invoice.
Coppell is a different animal from the rest of DFW. It’s one of the most HOA-governed cities in the metro, and nearly every established neighborhood has architectural review standards for gates: board width, stain color, metal finish, even hinge style. That changes how a repair ticket gets closed. We’ll get into that below, but know this now: we’ve done this dance with Coppell’s HOAs hundreds of times, and we won’t let you get fined for a repair that wasn’t approved.
Why Gatewood Fence & Gate Is Coppell’s Preferred Gate Parts & Welding Company
Coppell homeowners don’t call us because we’re the cheapest. They call because they’ve already been burned by someone who quoted one thing on the phone and handed over a different invoice at the door. Our pricing is upfront and written down before any torch gets lit. We also answer the phone around the clock with a live person, not a voicemail tree. That matters when your gate is stuck open at 11 p.m. on the day before you leave town.
Hal Gatewood started this outfit in 2001 and still answers the phone himself half the time. The shop has a published address and a license number anybody can verify. When we send someone to your driveway in Coppell, it’s a background-checked, uniformed member of Hal’s crew, not a rotating cast of subcontractors. The 90-Day Done Right Promise is printed on every invoice, not buried in fine print: if it’s not done right, one call brings us back.
We know Coppell’s gate stock like the back of our hand because we’ve repaired it for years. Cedar swing gates on corner lots. Ornamental iron drive gates with original LiftMaster operators. Slide gates on the larger properties near Northlake. The same gate problems show up again and again because the original construction followed a pattern, and we know exactly where to look before we even park the truck.
Our Gate Parts & Welding Services in Coppell
Our Gate Parts & Welding team handles the repairs that keep good gates working. We don’t sell you a whole new gate when a post, a hinge, or a weld will do the job. Fix the panel without the post and you’ll fix it twice. That’s the rule we work by.
Hinge Replacement
Hinges on Coppell gates fail in predictable ways. The bottom hinge carries most of the weight, and when Blackland Prairie clay shifts the post even a quarter inch, the hinge takes the strain until the weld cracks or the fastener tears out. We stock heavy-gauge hinges locally and weld most replacements on site, so the gate never leaves your driveway. A hinge replacement in Coppell typically runs $180 to $420 depending on the gate weight and whether the post itself needs reinforcement.
Post Replacement
In Coppell, a leaning gate post is almost never just a bad post. It’s the expansive clay underneath it, swelling after a wet spring and shrinking during summer drought. That cyclic heaving loosens the footing until the post walks out of plumb, snaps the weld beads at the base, and takes the hinges with it. We core out the old footing, set the new post deeper with a wider concrete base, and weld a steel insert where the original post was anchored. Typical post replacement in Coppell runs $850 to $2,200 including the footing work and re-hanging the gate.
Rail Repair
Swing gates sag when the hinge post moves, and the first thing to hit the ground is the bottom rail. It drags, then it bends, then the weld at the corner pops. Rail repair is straightforward for us: we straighten or replace the rail section and re-weld the corner joint, then re-hang the gate on corrected hinges. This is a same-visit job most of the time. You’re looking at $280 to $640 on average in Coppell depending on the gate size and material.
Custom Welding
Coppell’s HOAs create a lot of custom welding work. Off-the-shelf gate frames don’t match the architectural review specs, so we fabricate on site: reinforcing a rusted frame, extending a panel to close a gap, building a custom steel insert for a cedar gate that has to match an exact board width. We carry a mobile MIG welder and a full shop setup, so the work happens in your driveway. Custom welding starts around $200 for smaller reinforcements and runs up from there based on materials and scope.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Coppell
The original automated operators on Coppell’s 1990s and early 2000s homes are mostly LiftMaster and Viking, and those account for the biggest share of our operator retrofit calls. We’re certified to service nine major gate brands, and we regularly work on BFT, Linear, and Ghost Controls units in Coppell, plus the older Viking and LiftMaster systems still holding on. When a control board is obsolete with no replacement parts available, we match a modern UL 325-compliant operator to your existing gate and, where Coppell’s HOAs require it, to the approved finish and mounting style. Parts for common failures are on our trucks when we roll into Coppell.
Common Gate Parts & Welding Problems We See in Coppell Homes
- Posts leaning out of plumb from Blackland Prairie clay. Coppell sits on expansive soil that swells when saturated and shrinks in drought. The repeated heaving loosens post footings until weld beads crack at the hinge post and the gate starts dragging the bottom rail.
- Obsolete control boards on 1990s operators. The original LiftMaster and Viking units on homes built in the 1990s have control boards with no replacement parts anywhere. A dead board usually means a full operator retrofit that must match the HOA’s aesthetic specs.
- Ice-storm latch and rail damage. The February 2021 freeze hit Coppell hard. Latches froze solid, slide-gate rack teeth stripped when operators fought the ice, and rails bent. We still see gates with hairline cracks from that one event.
- Corroded hinge welds on older ornamental iron gates. Cedar fences may hide rot, but iron gates in Coppell’s older subdivisions have been through 25-plus North Texas summers. The welds at the hinge shoulders are the first thing to oxidize and fail.
Pricing for Gate Parts & Welding in Coppell, TX
Here’s honest money talk for Coppell. Hinge replacement typically runs $180 to $420. Rail repair lands between $280 and $640. Custom welding starts around $200 and climbs with materials and complexity. Post replacement with footing work is the expensive one at $850 to $2,200 because it involves concrete removal, a deeper footing, welding, and re-hanging the gate. Full operator retrofits for dead 1990s control boards usually run $1,100 to $2,800 depending on the unit and HOA compliance requirements. Every estimate is free, every price is quoted and agreed before any work starts, and we take $40 off any repair over $200. Call (903) 829-4499 for an exact quote.
We Also Serve Cities Near Coppell
Our crews work Coppell daily and make the trip to surrounding communities just as often. If you’re in Grapevine, Flower Mound, Euless, or Southlake, you’ll get the same live answer, same upfront pricing, and the same 90-Day Done Right Promise in writing.
Serving Coppell, TX - Our Local Coverage Area
We’re based in the Coppell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Coppell
Rebuilding a 1998 LiftMaster control board is generally not an option because replacement boards and individual board components stopped being manufactured years ago. What we can do is retrofit a modern UL 325-compliant operator to your existing gate, which usually runs $1,100 to $2,800 in Coppell including installation. We match the HOA-approved finish and mounting style where required, so you’re not fighting your architectural review committee. Call (903) 829-4499 and we’ll inspect the old unit and give you a written number.
It’s the soil, not the post. Northlake Woodlands and most of Coppell sit on Blackland Prairie clay that swells when wet and shrinks in drought, and the repeated heaving pushes a shallow footing out of plumb no matter how straight the post was initially. If someone straightened the post without widening and deepening the concrete base, it was a temporary fix. We core out the old footing, set a deeper post with a larger concrete footprint, and weld a steel anchor at the hinge post so the gate has something solid to hang from.
In most Coppell neighborhoods, yes. The city’s master-planned communities have some of the strictest architectural review boards in DFW, and many require written approval before you change a gate’s structure, finish, or board dimensions. We won’t close out the ticket until you produce the signed approval letter. We’re happy to provide specs, material details, and photos to send to your HOA committee, and we’ll wait for the signed letter before starting structural work.
Yes, and this is a practical retrofit for many older ornamental iron gates around Coppell. A solar operator with a battery pack mounts to the gate and post, no trenching or house wiring needed. The panel needs a clear southern exposure, which most Coppell driveways have. It’s not the right answer for every gate - heavier iron gates may need more torque than a solar unit delivers - but we’ll tell you honestly which way to go before you spend a dime.
Not always, though a stripped gear is a common culprit, especially after a freeze event put the operator under load. Grinding can also be a bent rail, a cracked roller, or debris packed into the rack teeth. We won’t know until we inspect it, but the fix is usually repairable rather than a full replacement. A slide-gate rail or gear repair in Coppell typically runs $220 to $600.
Call Gatewood Fence & Gate in Coppell
If your gate is leaning, dragging, grinding, or just dead, call us at (903) 829-4499. You’ll get a live person on the line, an honest estimate before any work starts, and Hal Gatewood’s name on the invoice. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Coppell since 2001.