Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in Coppell: What to Know First
Linear gate installation in Coppell typically runs $2,400 to $6,800 for a complete driveway gate with operator, depending on gate size, material, and whether you need a new post or can reuse the existing one. We’re an independent Linear service provider, which means we install and service Linear operators every week but we’re not tied to the manufacturer’s price book or their timeline. Most Linear gate installations in Coppell take one to two days once we’ve walked the site and ordered your specific gate, and you’ll know the full price before we start. If you’ve got a Linear operator already and just need the gate itself, that’s usually a one-day job. Call (903) 829-4499 and we’ll come look at your driveway, measure what’s there, and give you a written number you can hold us to.
How Linear Products Fail - and How We Fix Them
Linear makes solid equipment, but every brand has its weak spots, and we’ve seen enough of them in Coppell driveways to know exactly where to look before we start any installation.
- Linear LRA series gearbox wear. The LRA residential swing operators use a plastic-driven gear assembly that strips after years of Texas heat and daily use cycles. The symptom is a gate that hums but won’t move, or moves halfway and stalls. We replace the gear with either OEM or a machined aftermarket set and set the limit switches correctly so it’s not over-traveling, which is what killed the gear in the first place.
- Limit switch drift on Linear SL slide operators. The SL series uses mechanical limit switches that back out of adjustment over time, especially on gates that get a lot of wind load. You’ll see the gate stop short of fully open or slam into the end stop. We set them, lock them down, and test them through 30 full cycles before we call the job done. Half the Linear SL operators we see didn’t fail; they were installed with the limits barely finger-tight.
- Burned control board from ungrounded installs. North Texas gets real lightning, and a Linear operator on a metal gate post with no ground rod or a weak ground is a $400 board waiting to die. We always check the ground before we mount a new or existing Linear board, and we run a proper ground if the original installer skipped it, which happens more often than you’d think.
- Photo eye misalignment false-triggering. Linear photo eyes are sensitive to morning sun angles, especially on east-facing Coppell driveways. The gate refuses to close, or reverses for no reason. We align and shroud the eyes so the low Texas sun doesn’t blind them, and we test at the exact time of day you reported the problem when we can.
- Arm bracket fatigue on Linear swing gates. The bracket where the operator arm connects to the gate takes all the force, and on Linear swing installs it’s usually the cheapest piece of metal on the whole assembly. When it cracks, the gate sags and binds. We layout and weld a heavier bracket on site so it lasts longer than the original, and we do it without taking your gate off the hinges.
Our Linear Gate Installation Process
Here’s how a Linear gate installation goes when you call us in Coppell.
- 1
Call and talk to a person. You call (903) 829-4499, Hal or someone who works directly with him answers, and you tell us what’s going on with your gate and what you’re trying to end up with.
- 2
We come measure and look. We schedule a time, show up, measure your opening, check your posts, check the ground, check your existing operator if you have one, and figure out what actually needs to happen. No charge for the trip inside the county.
- 3
Written price, no surprises. We give you a written number before any work starts. If we find something when we dig or disassemble, we stop and tell you what’s different and what it costs. Nothing gets added to your invoice without you saying yes first.
- 4
The install. We set the gate, hang it, mount the Linear operator, run the power and safety edges, set the limits, program the remotes, and clean up. We weld on site, which means your gate never leaves your driveway on a trailer headed to some shop.
- 5
Test it like we’re the ones living behind it. We run the gate through full cycles, test the safety reverse, test the edges, test the keypad, and make sure the closer is working with the flow of your driveway traffic.
- 6
You get the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call and we’re back. That’s on every Linear install we do in Coppell.
What Linear Gate Installation Costs in Coppell
Here’s what we see for common Linear scenarios around Coppell. These are real ranges, not phone quotes.
- Full driveway swing gate with Linear LRA operator: $3,200 to $5,500
- Aluminum slide gate with Linear SL operator: $4,000 to $6,800
- Pedestrian gate with Linear keypad and magnetic lock: $1,100 to $2,400
- Replace just the gate panel, reuse existing Linear operator: $1,500 to $3,800
- Retrofit a new Linear operator onto an existing gate: $1,800 to $3,200
The gate material, whether we’re setting new posts, the length of the power run from your panel, and whether you want a keypad or vehicle sensor all move the number. We give free written estimates, and the price we quote is the price you pay unless something materially changes and you approve it first. Call (903) 829-4499 and we’ll come put a real number on your specific driveway.
Why Coppell Homeowners Call Gatewood Fence & Gate for Linear Work
Hal Gatewood grew up about a mile from Old Town Coppell, and he’s been working gates in this area since 2001. The name’s on the shop, the address is published, and if something’s not right you can drive over and look him in the eye. Every Linear installation we do carries the 90-Day Done Right Promise in writing, not buried in fine print. We answer the phone with a live person 24 hours a day, and the person who shows up is background-checked and wearing a uniform, not a subcontractor we’ve never met. We service nine gate brands, so when we’re working on your Linear operator we also know how it compares to LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, and we’ll tell you straight if something else would serve you better. $40 off any repair over $200, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Tell me what it’s doing wrong and I’ll tell you what it’s going to take, no runaround.
FAQs
Yes. We retrofit Linear operators onto existing Coppell gates all the time. We check the gate’s condition and weight first, because a heavy iron gate that sags will kill a new Linear operator in a couple of years regardless of the brand. Call (903) 829-4499 and we’ll assess whether your existing gate is worth putting a new operator on.
As an independent Linear service provider, we don’t file your warranty paperwork or act as a Linear authorized dealer. If your Linear operator is under manufacturer warranty, we’ll install it according to Linear’s specifications so the manufacturer’s terms are protected, but we can’t speak for Linear’s warranty department. What we do stand behind is our own 90-Day Done Right Promise on the installation work.
If we’re replacing an existing gate on good posts, it’s usually a one-day job. A full new driveway gate with new posts and a new Linear operator takes one to two days, and we’ll give you a firm schedule before we start. We don’t promise same-day on installations; good gate work is measured, ordered, and done right.
We use both, and we’ll tell you which one makes sense for your situation before we order anything. For control boards and safety edges, we use OEM Linear parts because the aftermarket versions are often the failure point. For gears and brackets where a machined aftermarket part is actually better than the original, we’ll use that and tell you why.
Yes. We install Linear-compatible keypads, vehicle exit loops, and safety edges on both new installs and existing Linear systems. We’ll wire everything in, program the remotes, and show you how it all works before we leave your driveway.
When you’re ready to talk about your Linear gate installation in Coppell, call (903) 829-4499. You’ll get a live person, a free written estimate, and a straight answer about what your gate needs and what it’s going to cost.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate - Coppell, TX at Gatewood Fence & Gate, serving Coppell and nearby areas.