FAAC Hinge & Roller Replacement Nationwide | Gatewood Fence & Gate

FAAC Hinge & Roller Replacement: The Coppell Owner’s Guide

We stock and install FAAC-compatible hinge and roller replacements for Coppell gate owners, with most single-gate jobs running between $185 and $340 installed. We keep common FAAC hinge and roller sets on the truck, so in most cases we can pull up, swap the worn part, and have your gate swinging right the same afternoon. Most folks around here call us when the gate starts dragging on the wheel track or when the hinge pin has worn an oval hole in the post bracket, and they can hear metal grinding every time the gate cycles.

Call (903) 829-4499

If your gate is binding, popping, or leaning slightly toward the free-swinging end, the hinge and roller set is usually the first thing we check after the post itself. On FAAC swing and slide gate systems used throughout Coppell, these parts take a beating from the Texas sun and clay soil heave, and they fail in predictable ways we can spot before a broken weld leaves your gate hanging.

Which FAAC Models This Applies To

The hinge and roller assemblies we replace are common across FAAC’s swing gate and slide gate lines, including the 413, 415, 422, S418, S450H, C720, and C721 series we service regularly in Coppell. FAAC hasn’t changed the basic mount geometry much over the years, but the hole spacing and pin diameter vary between the lighter residential units and the heavy slide gates. Before we quote anything, we measure the hinge pin diameter and the distance between the mounting holes, then match it against the FAAC parts chart for your specific opener model. That’s faster and more reliable than trusting a sticker that has been sunbaked for a decade.

On the OEM versus aftermarket question: for hinges and rollers, quality aftermarket sets from companies like DuraHinge and Gate Depot usually hold up fine here, but for the roller bearing itself, we have seen enough cheap imported bearings seize inside two summers that we will only put in sealed, greasable bearings, even if it adds eight dollars to the job. FAAC-branded hardware is well made, but you are paying a markup for the name. We will show you both prices and let you decide, though we are clear about which one has held up on Coppell’s limestone and concrete drive approaches.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• Metal-on-metal grinding when the gate moves. The roller bearing has gone dry or flat-spotted, and now the wheel is riding on the axle instead of rolling on it. Left alone, this carves the axle down until the wheel wobbles off.
• The gate drags or scrapes the ground near the latch post. The hinge bushings have wallowed out, and the gate has settled a half inch or more at the free end. You are not fixing that with a wheel adjustment; the hinge is the problem.
• The gate rocks or pops when it starts and stops. Loose hinge pins let the weight of the gate shift every time the FAAC operator kicks in, which is why you will feel a hard thunk through the drive arm.
• Visible rust streaks below the hinge barrels or around the roller axle. Texas humidity and sprinkler overspray will start that rust, and once the hinge pin rusts to the bushing, every cycle shaves metal off both.
• The gate hangs visibly lower on one side when open versus closed. That angle change means the hinge post brackets are flexing or the hinges themselves have bent. If we catch that on geometry alone, we can fix the hinge before the extra load kills your FAAC opener’s motor.

Replacement Cost & What’s Included

Here in Coppell, a full hinge and roller replacement for a single FAAC gate typically lands between $185 and $340 installed, depending on gate weight, hinge size, and whether we are replacing just the rollers or the complete hinge bracket set. A double swing gate with a center pull handle and heavier panel sections pushes toward the top of that range, and if the hinge post bracket has cracked and needs welding, that is a separate line item you approve before we strike an arc.

Every estimate is written and agreed to before any work starts, so there is no surprise on the invoice at the end. The price includes the new hinge pins, bushings, and roller wheels, fitting them to your existing FAAC brackets, greasing everything, and adjusting the gate so it sits square in the closed position. All of it is covered by our 90-Day Done Right Promise in writing; if a hinge bushing fails in 90 days, we come back and make it right, no runaround. We do not charge a trip fee inside the county, and we are happy to give you a free second opinion on any written estimate you already have.

DIY or Call Us?

You can safely check a few things yourself: watch whether the gate is dragging at one end, grab the gate near the hinges and lift to feel for slop, and look for rust streaking or a wheel that is not turning. That tells you where the problem is, but the repair itself is where we have seen owners get hurt. A loaded swing gate carries a lot of stored weight, and when a hinge pin lets go mid-removal, that panel can drop or swing hard enough to break fingers or pin a leg. This is a job for someone who has braced the panel, set up stands, and removed a hinge pin a hundred times without letting the gate move.

We fix this kind of thing in driveways all over Coppell, so you don’t haul the gate anywhere. Tell me what it’s doing wrong and I’ll tell you what it’s going to take, no runaround. If you would rather have one of us look at it first, call (903) 829-4499 and we will come out and tell you straight what it needs, free.

FAQs