Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Coppell: What to Know First
FAAC gate access control repair in Coppell typically runs $180 to $400 for common failures like dead keypads, unresponsive receivers, or blown control boards, and most jobs are done the same day we look at it. We’re an independent FAAC service provider, not a manufacturer rep, which means we fix the board or the wiring instead of telling you to buy a whole new operator. If your FAAC keypad quit talking to the gate, or the remote worked yesterday and not today, call (903) 829-4499 and a live person answers.
This page is for Coppell homeowners who own a FAAC gate operator and want straight answers about access control: keypads, phone entry, card readers, video intercoms, and remotes. No brand gloss. Just what fails, why it fails here, and what it costs to make it right.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 Series keypad dead after a hard rain. The 400-series operator (common in Coppell’s older subdivisions like Northlake Woodlands) runs its keypad wire through a conduit that wasn’t always sealed right at the post. Water gets in, corrosion eats the connection at the terminal block, and the keypad stops responding while the operator still works. We pull the wire, cut back the corroded section, re-terminate, and seal the conduit so it doesn’t happen again next spring.
- FAAC E124 / S418 receiver stops learning remotes. When the receiver stops accepting new remote programming, nine times out of ten it’s a weak memory battery on the control board, not a failed receiver. FAAC doesn’t exactly advertise this. We replace the battery for a few dollars instead of selling you a new board for a few hundred.
- Phone entry system opens the gate but never closes it on schedule. On FAAC operators wired into a telephone entry unit, the auto-close timer lives in the operator’s control board programming. If a previous tech left the auto-close disabled (common after a panic-mode override), the gate opens fine but sits there until you close it manually. We restore the timer settings through the board’s programming menu and test the safety loop so it closes on time without pinching a car in the driveway.
- Card reader at the street beeps but the gate won’t budge. Almost always a relay contact burned out on the access control relay module, not a card or reader problem. FAAC uses a low-voltage trigger circuit, and over years of Texas heat and lightning-surge exposure, those relay contacts pit and fail. We replace the relay, not the reader, and add a surge suppressor so the next storm doesn’t do the same thing.
- FAAC hydraulic operators slow down in summer. This one’s specific to Coppell’s July and August heat. FAAC hydraulic units (like the 750 and 770 series on larger estate gates) can run sluggish when the oil thins out in triple-digit temperatures, which makes the gate creep or trip the obstruction sensor. It’s not the operator wearing out. It’s the fluid and often the bypass valve needing adjustment for our climate. We set the pressure relief and flow rate for Texas, not for the factory default that assumed a cooler place.
Our FAAC Gate Access Control Process
Here’s how a typical FAAC access control job goes from your first call to the gate working again:
- 1
You call (903) 829-4499. A live person answers, day or night. You tell us what the keypad, remote, or reader is doing wrong. No voicemail, no call center three states away.
- 2
We show up in the window we gave you. We don’t do four-hour arrival windows. We tell you when we’ll be there, and we’re there. Hal Gatewood or one of his crew, uniformed and background-checked.
- 3
We start with the symptom, not the sales pitch. The first thing we do is watch the gate do the thing you said it does. Half the time the problem is not what a parts-changer would guess. On a FAAC 400 series keypad failure last month in Coppell, the fix was a corroded wire nut, not a new keypad.
- 4
We give you a written price before we touch a screwdriver. You agree to the number first, and the number doesn’t change when the job’s done. That’s how it works here.
- 5
We fix it with the right parts. We carry genuine FAAC boards and receivers, and when a quality aftermarket part is the better call for an older unit, we tell you why and let you decide. We don’t put a $30 knockoff relay in a ol,200 operator without saying so.
- 6
We test it like we’re the one who’ll get the 2 a.m. call. We cycle the gate a dozen times, trigger the safety sensors, try every remote and keypad code, and stand there watching it until we’re satisfied. Then we hand you the 90-Day Done Right Promise in writing and an invoice with Hal’s name on it.
What FAAC Gate Access Control Costs in Coppell
Fair question, and we answer it straight. Here’s what we typically see on FAAC access control work in Coppell:
- Keypad repair or replacement: $95 to $250, depending on whether we’re fixing a corroded connection or installing a new weather-sealed keypad.
- Receiver or remote programming: $80 to $180, including all your existing remotes reprogrammed and tested.
- Control board repair: $150 to $350. A new FAAC board can run higher, but we often repair the board on the bench for less.
- Phone entry or card reader integration: $220 to $450, including the relay wiring, programming, and testing the safety loop.
- Full access control upgrade (new keypad, receiver, phone entry): $500 to $900, quoted before we start and held to the penny.
What moves the price? Distance of the keypad from the operator, condition of the existing conduit, whether the board is repairable or truly dead, and how much of the wiring a previous installer left in bad shape. An estimate is free. Always.
Why Coppell Homeowners Call Gatewood Fence & Gate for FAAC Work
We’ve been working on gates in Coppell since 2001, when Hal Gatewood decided he’d rather fix things with his hands than sit in an office. The shop is local, the address is published, and the name on the invoice is the name of the guy who owns the place. When we fix a FAAC access control problem, we weld on site, we repair what’s repairable, and we don’t sell you a new operator because a $4 relay failed. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, we make it right, one call, no runaround. And if your FAAC unit is beyond saving, we’re certified on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, so you don’t have to start your search over.
FAQs
In most cases, yes. Common FAAC access failures like a dead keypad, a receiver that won’t learn remotes, or a burned relay are diagnosed and fixed on the first visit. If we need a specific FAAC board or receiver that isn’t on the truck, we’ll tell you exactly when it’s coming and get you back on the schedule without you having to chase us. Call (903) 829-4499 and we’ll tell you straight what the turnaround looks like for your specific problem.
No. As an independent FAAC service provider, we’re not authorized by the manufacturer, but the repair work we do on your gate doesn’t void a FAAC warranty that’s still active. Texas law protects your right to choose who works on your equipment. When your FAAC unit is under warranty and a part fails that’s covered, we’ll point you to the warranty process and handle the labor. When it’s out of warranty, we fix what’s there.
Both, and we tell you which one we’re proposing and why. Genuine FAAC boards, receivers, and keypads go in when the unit is newer or when exact signal timing matters. On older FAAC models where the OEM part costs more than the gate is worth, a quality aftermarket relay or receiver can be the sensible call. We never swap in a cheap part without telling you first, and we stand behind either choice with the 90-Day Done Right Promise.
Usually it’s neither. On FAAC 400 and E124 units, the most common cause we see in Coppell is a corroded or loose connection between the keypad and the operator’s input terminal. The keypad beeps because it’s alive; the gate doesn’t move because the signal isn’t reaching the control board. We test the wire run, the terminal block, and the relay trigger before we ever sell you a part.
A new FAAC control board typically runs $250 to $450 installed, depending on the model. Before we quote that, we check whether the existing board can be repaired. We’ve bench-fixed FAAC boards for $150 or less when the failure was a blown capacitor or a burned relay, and that’s a far cheaper fix than a board swap. Call (903) 829-4499 and tell us what your gate is doing, and we’ll give you a straight answer about which route makes sense.
Yes. Most FAAC operators, including the 400 series, E124, and hydraulic estate units, accept a low-voltage trigger from a video intercom or smart access system. We install the intercom at the street, run the control wiring, and program the operator’s input so the intercom button opens the gate. We’ll also wire the safety loop so the gate won’t close on a delivery truck, which matters on busy streets.
Call Gatewood Fence & Gate for FAAC Gate Access Control in Coppell
If your FAAC keypad, remote, phone entry, or card reader is acting up, call (903) 829-4499. A live person answers, we give you a straight answer about what it’ll take, and the estimate is free. No trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Tell me what it’s doing wrong and I’ll tell you what it’s going to take, no runaround.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate - Coppell, TX at Gatewood Fence & Gate, serving Coppell and nearby areas.