Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Coppell: What to Know First
FAAC gate installation in Coppell typically runs $900 to $2,800 depending on whether we’re setting a new operator on an existing gate or building the gate and running the power from scratch. Most FAAC installs in Coppell take one full day, and we quote the price in writing before any work starts. You won’t open the invoice and find a surprise.
This page is for Coppell homeowners who already own a FAAC operator, or are weighing one against other brands, and want the install done by somebody who knows the equipment well enough to catch setup mistakes before they turn into service calls. If you’ve got a FAAC box sitting in the garage or a gate that’s never opened right since the day it went in, call (903) 829-4499 and tell me what it’s doing wrong and I’ll tell you what it’s going to take - no runaround. We’re an independent FAAC service provider, not a factory arm, which means we call problems what they are instead of what the warranty manual says they should be.
How FAAC Products Fail - and How We Fix Them
- FAAC 400 Series swing operators losing their limit memory. The 400 series hydraulic swing units are common on Coppell driveway gates in neighborhoods like Northlake Woodlands and Lakes of Coppell. What we see after a storm or a power blink is the operator forgetting its open and closed limits, so the gate slams or stops six inches short. That’s not a dead motor. It’s the control board’s memory getting knocked loose, and the fix is reprogramming the travel limits and checking the grounding. We’ve saved Coppell owners a full operator replacement more times than I can count by starting there instead of selling a new unit.
- FAAC 770 hydraulic operators with weeping cylinder seals. The 770 is a workhorse on heavier sliding gates, but the hydraulic seals get brittle in the Texas heat. You’ll see a thin oil film on the ram and the gate moving slower every week until it crawls. We replace the seal kit and refill with the specified hydraulic fluid. A lot of companies won’t touch hydraulics and will tell you the operator’s done. Hal rebuilt hydraulic systems before he ever touched a control board, so this is a regular Thursday for us.
- FAAC S418 and S450 sliding gate operators throwing false obstruction faults. These compact sliding units are sensitive to debris in the rack and pinion track. Coppell’s clay soil tracks grit onto the rack, and the amperage sensor reads that extra drag as an obstruction, so the gate reverses for no visible reason. We clean the rack, adjust the torque trim, and verify the force settings match the gate’s actual weight. Half the “obstruction” calls on FAAC sliders around Coppell are just dirt and a torque dial that was set at the factory for a lighter gate.
- FAAC E024U control boards with chewed auxiliary terminals. This is a Coppell-specific one: field mice and rats love the warm control box on a FAAC operator, especially near the creek corridors around Cottonwood Creek and Denton Creek. They nest in the enclosure, chew the low-voltage wiring to the keypad and photo eyes, and then the gate won’t close. We rewire the damaged circuits, seal the enclosure entry points with mesh and conduit putty, and test every accessory before we leave. The board itself usually survives. The wiring does not, and no factory manual tells you that.
- FAAC 391 and 770 underground operators with flooded foundations. Underground FAAC units in Coppell sit in a steel pit that becomes a bathtub after a hard North Texas rain if the previous installer didn’t run a proper drain. The motor runs, then trips, then runs again, and the gate half-opens. We pump the pit, fix the drainage so water moves away from the housing, and replace corroded wire nuts with sealed connectors. If your FAAC is in the ground and it’s been acting haunted after rain, this is where we start looking.
Our FAAC Gate Installation Process
- 1
Call and tell us what you’ve got. A live person answers at (903) 829-4499. We ask what FAAC model you have, what the gate is made of, and what it’s doing or not doing. If you don’t know the model, we’ll find it on the unit when we arrive.
- 2
We come out and look at the whole gate, not just the operator. A gate sags in the hinge post, not in the middle, and that is where we start. We check the hinges, the post anchors, the wheel track if it’s a slider, and the operator mounting. A FAAC unit installed on a sagging gate will fail early, and no brand on earth fixes a bad hinge post.
- 3
We make the parts decision with you. For FAAC work we use OEM components when the part is safety-critical, like control boards, photo eyes, and hydraulic seals. For non-critical mounting hardware and brackets, we’ll use quality aftermarket equivalents that cost less and hold up in Coppell’s humidity swings. You’ll know which is which before we order anything.
- 4
We install, set limits, and test under load. We mount the operator, run the power, set the open and closed limits, adjust the force settings to match the gate’s actual weight, and wire in the safety edges and photo eyes. Then we test the gate twenty cycles in a row, both directions, with the obstruction sensors checked each time.
- 5
We walk you through it and hand you the Done Right Promise in writing. Every FAAC job gets our 90-Day Done Right Promise stamped in writing: if it’s not done right, we make it right. One call brings us back, no runaround.
What FAAC Gate Installation Costs in Coppell
| FAAC Installation Scenario | Typical Price Range in Coppell |
|---|---|
| Install FAAC operator on existing single swing gate (operator only, power already at gate) | $900 - $1,500 |
| Install FAAC operator on existing double swing gate with two operators | $1,600 - $2,400 |
| Install FAAC sliding gate operator on existing slide track | $1,100 - $1,900 |
| Full install: new gate built on site plus FAAC operator, power run from house | $2,200 - $2,800+ |
| FAAC underground operator foundation work, including pit drainage fix | $1,400 - $2,300 |
What moves the price in Coppell: whether power is already at the gate (a trench run through clay is real labor), the gate’s weight and whether it’s steel or ornamental iron, whether we’re setting new posts, and whether the existing gate needs hinge or track repair before the operator goes on. You get the number before we start, and it does not change at the door. Call (903) 829-4499 and we’ll come measure and price it free. No trip charge inside the county.
Why Coppell Homeowners Call Gatewood Fence & Gate for FAAC Work
Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is. We’ve been fixing and installing gates since 2001, and we’re not passing through. The person who answers your call is the same person who shows up in the driveway, and we don’t have a phone tree.
We service FAAC alongside eight other major brands: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, BFT, Linear, Viking, and Elite. That matters because when a Coppell homeowner asks whether they should stay with FAAC or switch, we’re not protecting a dealership quota. We tell them straight which operator fits their gate, their budget, and their patience for maintenance. Every FAAC install carries our 90-Day Done Right Promise in writing. If it’s not done right, we make it right. And we offer a free second opinion on any written estimate, so if another company told you the whole gate needs replacing, we’ll come look and tell you the truth. Fix the panel without the post and you’ll fix it twice. We’d rather fix it once.
FAQs
We’re an independent FAAC service provider, not a factory arm, so the manufacturer warranty on a FAAC operator is between you and FAAC. We install to factory spec using OEM parts where safety and reliability depend on it, which keeps your warranty a valid path if you ever need it. Our own work carries a 90-Day Done Right Promise in writing. Call (903) 829-4499 and we’ll walk you through what a specific install involves.
In most Coppell cases we can install a FAAC operator on your existing gate, as long as the posts and hinges are sound and the gate isn’t sagging so badly it drags. We’ll tell you honestly if the gate is beyond saving, but our repair-first philosophy means we’re not selling you a new gate unless the old one is genuinely unsafe or too far gone. A free estimate tells you which road you’re on.
Most FAAC installs in Coppell take one full day from start to finish, including limit setting and testing. If we’re building a new gate on site or trenching a power run, you’re looking at two to three days depending on the gate’s size and the soil conditions. We’ll give you a window when we quote, and we show up in it.
We keep common FAAC components on hand, including control boards, photo eyes, seal kits for the 770 hydraulic series, and safety edges. Specialty items we don’t stock are typically in hand within a week through our local supply network. We’ll tell you the wait time before we order anything you have to pay for.
We answer the phone around the clock and we make same-day runs in Coppell whenever the schedule allows, which is more often than not for a gate that’s stuck. If your FAAC operator has locked the gate shut or left it standing open, we take that seriously. Call (903) 829-4499 and a live person picks up, day or night.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate - Coppell, TX at Gatewood Fence & Gate, serving Coppell and nearby areas.